Archive for January, 2015

The Human Ear

Posted By Andy Kos

Something often overlooked, but I believe to be an important part of designing, building and configuring loudspeakers systems is understanding some of the basics of the human ear, and the effects of sound on the human body. This article is intended as a brief introduction, and is by no means exhaustive.

The smiley face equaliser

img1

I’m sure you’ve seen this used, and possibly even done it yourself at some point in time.

Some would argue this is wrong, others that it is right.

The ‘smiley’ face curve often seen on graphic equalisers is similar to the effect achieved by the ‘loudness’ button on many hi-fi systems. It boosts the bass and treble to make it sound ‘better’ – but why do we think it sounds better?

Is it the speakers arent working properly? Maybe… we’ll discuss this later

But is something else wrong?

You might assume your ear works like a high quality studio microphone, with a flat frequency response across the audio spectrum, research has shown this is not the case. The way the ear responds to different frequencies varies considerably.

human ear

 

The graph above shows lines of perceived equal volume. First thing you will notice is that the smiley face equaliser curve is remarkably similar to the frequency response of the ear, but offset a little with the centre point around 3kHz and more emphasis on low frequencies. To some extent the smiley face can be explained as just naturally compensating for the human ear, making lower volume program material sound like we would expect it to sound at high volume.

Key Points:

Essentially deaf to bass frequencies:  This goes some way to explaining the loudness functions on hi-fi systems, at low volume, we find bass very difficult to hear, and it needs boosting significantly. As the volume increases the curve flattens, requiring less bass boost. In effect the loudness function is giving our ears the same balance as ‘loud’ music, but at low volume. Many people are unable to hear detail in bass frequencies, and some actually prefer the sound of distortion in bass frequencies, as they feel the sound is ‘warmer’

Most sensitive to mid-range frequencies peaking at around 3-4 kHz: Approximately the same frequency as a human high pitched scream or yell, which is not dissimilar to a baby’s cry. This means our ears are most efficient at detecting important sounds, research suggests this is down to years of evolution. Many alarm designers utilise these frequencies to maximise effectiveness. With out ears being so sensitive in the mid frequencies, poor quality sound, particularly distortion will be extremely noticeable, perhaps this goes some way to explaining the smiley curve; a way of masking problems in the mid-band by overpowering with bass and treble? Many people find distortion in the upper-mid frequencies painful, and this is often linked with occurrences of tinnitus.

Response varies with volume: As the volume increases, our ears hear differently. This is one of the reason many high-end large scale PA Systems utilise Dynamic EQ, where the equalisers are programmed to change as the volume increases. If you do apply equalisation to your sound system, you may need to adjust it for low/high volume.

So is the smiley curve correct? In my opinion, most of the time it isnt, particularly if you are playing back pre-recorded music the original recording will have been tweaked by the engineer to sound ‘right’. What is definitely correct is to equalise your system to make it sound right at the volume it is being used, and the room it is being used in, and the type of program material being played through it. If this happens to be a smiley curve, so be it, but as a system operator you should resist the urge to just boost bass and treble in the hope it will sound better. If you find you are doing this a lot, you might want to consider upgrading your sound system.

 

 

Be the first to comment
Filed in Science of Sound, The Human Ear | Tagged: , , , , ,

Totally Addicted to Bass?!?

Posted By Andy Kos

Its well known that a heavy bass line is in dance music is often very popular, and many people believe it is absolutely essential in order to create the best atmosphere for certain styles of music, but could we actually be addicted? Some people think it may be possible, and there is some research to suggest they are right.

To understand how this may be possible, we need to understand how sound affects our bodies. In modern life, one of our primary needs to hear is to communicate, often at moderate volume, but our ears can be much more useful than this, allowing us to be aware of things further away than we can see, and some of these things may help explain how our bodies react to sound.

Thousands of years before we had amplified music, bass frequencies, and how we reacted them, could have been critical to our survival. In nature, loud sounds, with an emphasis to low frequencies are often connected to danger. Just think of the sounds created by a stampeding herd of animals, an earthquake or a volcano erupting. Research suggests that years of evolution have developed the ‘fight or flight’ response in humans when presented with danger, this stimulates the production of adrenaline, enhancing the bodies ability to react to the danger.

You’ve heard of adrenaline junkies right? Well, it is possible that the brain associates high levels of bass with pleasure due to the mild adrenaline rush that bass frequencies may cause, and over time, coupled with other stimulants, could contribute to an addiction.

Another field of research suggests exposure to very high sound pressure levels (commonly found in bass frequencies) damages our ears and causes ‘pain’, however our bodies naturally react to this pain by creating numerous chemicals within the body, including adrenaline, endorphines and encephalons, collectively acting to blunt pain, but at the same time causing a pleasure enhancing morphine-like effect. This has yet to be proven, but the theories seem to hold true, and could also contribute to this concept.

One researcher has even gone as far as to suggest that extreme bass frequencies that penetrate the human body, causing you to literally ‘feel the bass’ may cause temporary damage to cellular structures within your body, cause the same pain blocking chemicals to be produced. These chemicals make you ‘feel good’ and may go some way to explaining the positive feeling experienced by high intensity bass frequencies.

So, is it possible to be totally addicted to bass?

Maybe….

 

 

Be the first to comment
Filed in Science of Sound, The Human Ear | Tagged: , , , ,

What Power Driver Do You Need?

Posted By Andy Kos

What’s up with the Watts?business path choice

Choosing the right driver for your speakers can be something of a minefield, particularly if its your first time. There are a number of things to be aware of, one of which is the power rating (specified in Watts)

Technological advances in materials are allowing Loudspeaker drivers to be developed with larger power handling, at the same time we have seen some loudspeakers drivers have their power ratings changed, with increases of 25% or more, but with apparently no change to the driver. Add to this the confusion of RMS Power, Continuous Power, Program Power, and Peak Power and it’s not suprising some of you are getting confused. This article aims to explain some of terms used, and dispel a few myths.

Q: My amp is rated at 400W per channel, will a 600W driver break my amp by drawing too much power?

A: NO. The power rating of your amplifier is a measure of how many watts it can deliver to the speakers before it reaches the limitations of its internal power supply and starts to clip/distort.  The power rating of your speakers is the maximum power they can accept from an amplifier before they are in danger of overheating and burning out. Providing you have the corrent impedance load, your speakers are unable to draw more power than the amplifier is willing to give. https://speakerwizard.co.uk/impedance-faqs/

Q: If I replace my 400W speakers with 450W speakers will they go louder?

A: Not necessarily, the limiting factor is generally your amplifier, if you amp is rated at 400 Watts, you wont get any more than 400W output without severely distorting the sound, and potentially damaging your amplifier. If your amp can output 450W, then an increase in power handling may make your speakers go a little louder, but its possible they may be no louder, or in some cases quieter. The key factor here is efficiency, some speakers are more efficient than others. If you have two speakers operating at the same power level, and one is more efficient at converting electricity into sound, it doesnt take a rocket scientist to figure out which of the two will be louder. Most manufacturers give an indication of efficiency using the sensitivity figure measured in db@1W/1M (link to sensitivity)

Q: Which power rating should I look at?

If you’re reading this, chances are you are a novice, so for simplicity we suggest you use the continuous RMS power rating. Luckily, this is the one most manufacturers specify. You may also see Music Program Power Ratings, typically these are double the  RMS power rating. If you see a peak power rating, its often meaningless, and serves little purpose. Peak power ratings are often four time the RMS rating, so if you see this anywhere, divide it by 4 to give you an idea of the real power rating.

Q: What do the power ratings mean?

RMS Power.

Sometimes referred to as Average Power, or Continuous Power. The term RMS here is incorrectly used, it is not RMS power in the true sense of the term, as Power does vary from positive to negative, it is the Voltage. The RMS Voltage is used in the power calculation, hence giving rise to the term ‘RMS Power’.

Over the years, various standards have been used in this ‘RMS Power’ calculation, including;

The IEC268-5 (1978) standard (IEC = International Electrotechnical Commission)

The EIA RS-426-A (1980) standard (EID = Electronic Industries Association)

The AES2-1984 standard (AES = Audio Engineering Society)

The AES2-2012 standard – which is becoming the most commonly adopted standard. Previously many manufacturers used the EIA standard, re-ratings some speakers using AES saw increases in power ratings of 25%, sometimes more. One example we are aware of was a high power 18″ driver, which was previously rated at 600W, and had the power rating changed to 800W overnight – with no changes whatsoever to the speaker design.

How is this possible? The AES power rating has a higher crest factor than the EIA rating, and is also for a shorter duration 2 hours for AES whereas the EIA rating was over an 8 hour test period. Some would argue this is not a totally realistic test. However for the layman, it is a useful benchmark for matching up driver power to speaker power. We’ll explain why:

Music Power:

Also know as Program Power, this is an indicator of the power rating of speaker use with ‘typical program materal’, which most of us call music. The RMS Power test is not done with music, it is generally done with bandwidth limited pink noise, which is a continuous signal. When was the last time you played music that sounded like static? Not often I bet. Music power takes into consideration that a bass beat is not continuous, it is a series of pulses. In between the pulses, there is no power being applied to the speaker, so when you average out the power over time, you can handle much more power.

What does this mean? Well you can exceed RMS Power for short periods of time, but not with a continuous signal. So if you play average music, you can usually run above RMS Power level quite happily in most instances, and with appropriate limiters in place, somewhere between RMS power and Music Power is generally a safe level. This is why I’m saying the Music Power is a useful benchmark – it helps determine amplifier power choice ‘roughly’ and is a good level to aim at to keep your drivers operating within safe parameters, if like most people, you try to push things just a little harder every now and then, you should still be fine, just as long as you don’t start treating music power as a long term continuous power rating, as you will almost certainly cause your speakers to fail if you do this.

Peak Power:

This is the maximum short term power that can be applied to the driver, and is typically calculated to be four time the RMS Power. I recommend you dont use Peak Power for anything except bragging to someone who doesnt know anything about sound.

Should I buy the most powerful speakers I can afford?

Probably not – It’s best to get speakers appropriate to your requirement. This is partly due to how speakers work. High power speakers are designed to have a high excursion (thats lots of cone movement) – in order to be able to handle the extra power, they typically have stiffer components, particularly with regard to the suspension. These high power speakers require a certain amount of power to overcome the mechanical resistances of the suspension. Comparing two extreme examples, of say a 100W speaker and a 1000W speaker running bass. The 100W speaker will have a low output for say, the first 5-10W put into it, once you are putting in 50W or so, the speaker will be at half its rated power, and will be (depending on sensitivity) fairly loud, ramp it up to 90-100W and the driver is giving all it can, potentially operating at its most efficient point. Lets suppose you only have a 100W amplifier, the 100W speaker will give you more output than the 1000W speaker. If you put your 1000W woofer on the end of your 100W amplifierm the first 40-50W of power will be used inefficiently, just to overcome the stiffness and resistance of the suspension, ramp it up to 100W, and you are still only tickling the 1000W woofer, you will find that you may need 200W running through the 1000W woofer to be as loud as the 100W woofer. As you keep ramping up the power, the 1000W woofer will ultimately create a lot more sound output than the 100W speaker ever will, but if you only have a small amplifier, you are better off with an appropriately matched driver.

So what if I exceed the power ratings?

You run the risk of overheating the voice coil of the speaker, and causing it to fail – but be careful – just keeping an driver within it’s recommended power rating is no guarantee of longevity. You also need to be away of excursion (often specified using Xmax and Xlim) as you can damage an driver through over-excursion without exceeding the power rating.

What about Power Compression?

Power compression is the little bugbear that can upset your best laid plans, and give you reason to throw the manufacturer’s specifications out the window. Many manufacturers choose to ignore power compression, some actively avoid specifying it or even mentioning it.

The sensitivity (efficiency) manufacturers specify is measured at a power level of 1W at a distance of 1m from the speaker. At 1W, very little heat is lost within the voice coil, so the driver is more effective at converting electricity into sound.

Its very common for loudspeaker voice coils to be wound from copper, which has a positive temperature co-efficient of +0.393% per degree C. It’s quite feasible for the voice coil of a high power speaker to reach 200 degrees Celsius, which could mean a change in the resistance of the wire to increase of 50% or more. Your 8 ohm driver will no longer be an 8 ohm driver, and the nominal impedance could rise to as high as 13 or 14 ohms. At full power, many drivers are no longer operating at their stated impedance, and they generating a lot of heat.

A good quality driver, with low power compression at its full rated power, could be 3-4 dB louder than a driver that suffers badly from power compression. Many modern designs are taking account of this, and making efforts to ensure driver cooling is maximised to counter the effects of power compression.

 

 

 

 

 

 

 

 

 

Be the first to comment
Filed in Loudspeaker Driver Parameters, Power | Tagged: , ,

Power Compression

Posted By Andy Kos

When selecting speakers, it’s common for people to just look at maximum power handling, and many manufacturers make a point of specifying seemingly unbelievable power handling capacity of 1000W or more. Its quite rare for manufacturers to specify power compression though, and it seems to be often overlooked by system designers.

It seems that loudspeakers to handle what appear to be insanely high levels of power compared to 10 or 15 years ago. Has there been some amazing technological breakthrough? Do we need to re-write the physics text books? No, it’s still just basic physics – so what are the changes?

Firstly, modern materials used in the construction of voice coils are able to withstand significantly higher temperatures before failing.  Why is this important? Well Cone loudspeakers are in fact very inefficient, with even the best transducers only converting around 5% of the electrical energy supplied into sound, the majority of the remainder is converted into heat. So a 1000W bass speaker running at full power may well be converting only 50W into acoustic power, and 950W of heat. Thats like having a 1kw bar heater in your bassbin! That’s a lot of heat, which can cause big problems.

Aside from improving construction materials, manufacturers are also refining designs to maximise heat transfer away from the voice oil, this also contributes to the increases in power handling capacity we are experiencing.

What’s all this got to do with power compression?

Enabling speakers to handle much higher temperatures might seem a good thing, as it increases maximum power handling, but it also has a detrimental effect. Most voice coils are made from copper or aluminium wire, both of which have a positive temperature co-efficient of around 0.4% per °C. What’s the significance of that? You will have heard of superconductors, which operate at extremely low temperatures in order to try to reduce and minimise resistance.  Loudspeaker voice coils  unfortunately work in the opposite way: as the temperature increases, the resistance also increases.

A modern state of the art voice coil is designed to withstand extremely high temperatures, often operating at up to 3000C or more when driven at full power. 0.4% may sound insignificant, but remember this is per °C – at only 2300C the voice coil DC resistance has almost doubled which causes the voice coil impedance to increase accordingly. Some simple maths and you can quickly see that the increase in temperature  can make your 8 ohm speaker start behaving more like a 16 ohm speaker.

So after setting your sound system carefully at the start of the night, an hour in, and it doesn’t sound as loud – you might wonder whats going on. Two things: firstly, your ears have a self defence mechanism: there are 2 tiny muscles in the middle ear that will contract when the ear is exposed to loud sounds. This contraction will reduce the loudness of the sounds reaching the inner ear, thereby protecting the inner ear against exposure to loud noises. This isn’t power compression, but it’s something to be aware of, as you may well be tempted to turn up the volume, I know from experience that a typical DJ will certainly try this, and end up running his mixer into overdrive in the attempt to get more volume.

The second factor is power compression, a typical loudspeaker can lose 3-6 dB of volume once power compression kicks in.

You could think of power compression a bit like the aerodynamics of driving a car. When you start moving, a certain level of power from your engine sets you hurtling forwards at high speed, but as you go faster, wind resistance increases, so you stop accelerating. You need to apply more power to increase speed, but wind resistance keeps increasing too, so you have to apply even more power.

If your amplifiers have headroom, your instincts will make you want to turn them up, to restore the original volume level. To some extent this will work, if you’re familiar with the maths, you’ll see whats going on. Your 8 ohm speaker at room temperature happily accepts 1000W from your amplifier, and gradually reaches an operating temperature of say 250°C. Your resistance has doubled, and your ‘new’ 16 ohm speaker will probably only be receiving around 500W from your amplifier. In a way, as the speaker reaches temperature, it ‘protects itself’ by reducing the power it is operating at, stopping it getting any hotter. If it were to cool a little, the power would increase again, causing it to heat up.

Lets suppose you turn the gain up on your amplifiers, determined to try to push 1000W through your speakers. As you apply more power, you will generate more heat,  perhaps reaching 350°C or more, with your speakers resistance continuing to increase to perhaps 20 or more ohms. Essentially you are fighting a losing battle, as you turn the gain up, the speaker fights back with a higher resistance. You will eventually reach a limit, either your amp will run out of headroom and you cant turn it any louder, or the other possibility, which happens all too often, is your speaker will overheat, and burn out causing catastrophic failure.

Now you know about power compression and the fact that speaker resistance increases with heat, you’ll probably realise that you actually have to push a speaker very hard in order to cause it fail – so if your speaker suddenly fails and you smell burning, the only person to blame is YOU, as you now know better than to try to fight power compression by applying more power.

Now consider what effect power compression will have. 3-6dB loss at full operating power is almost like switching off half your PA system. To achieve the same consistent volume you will need twice as many speakers!

What’s the solution? Either buy speakers with headroom, e.g. if you want to operate at around 500-600W, you might want to consider purchasing speakers rated at 800W or more. At 75% of rated power, the effects of power compression should be much less significant. Also, try to select speakers with improved cooling technology, that suffer less from power compression. Avoiding power compression could make your speakers twice as loud, meaning you could take half as many to the gig!

There are other side effects from the increased levels of heat in a speaker, T/S parameters can vary, bass can sound boomy and mid frequencies can sound muffled. For the best sound quality, its best to try to  minimise power compression effects,

 

 

Filed in Loudspeaker Driver Parameters, Power | Tagged: , , , , , , , ,

Impedance – FAQs

Posted By Andy Kos

How do I know what impedance load I have?

Most manufacturers will specify impedance, and will include it in the product specifications, often printing it on the speaker itself. If you don’t have this information, you can measure the DC resistance using a multi-meter (please note Resistance is NOT Impedance – find out why here: https://speakerwizard.co.uk/impedance-and-resistance-whats-the-difference/

You should only measure the resistance of speakers when they are not in use, and not connected to an amplifier. By putting your multi-meter probes on each terminal of the speaker you will get the DC resistance, which can be used as a guide to get the impedance. A DC resistance of 5-6 ohms is normal for a driver with 8 ohm impedance, around  12-13 ohms  is common for  a 16 ohm impedance driver, and  3 ohms DC resistance would be normal for a 4 ohm impedance. You may notice that moving the cone whilst checking the resistance will make the reading change, this is because the voice coil is moving in a magnetic field, which will induce a voltage in the  coil, which in turn will affect the multimeter’s measurement.

Many loudspeaker manufacturers will label the drivers to make identification easier, Eminence for example include a suffix on the drivers, for example the Beta12A is the standard model, and is 8 ohm impedance, the letter A designated 8 ohm impedance. The Beta 12B is 16 ohm impedance, and the Beta 12C is 4 ohm impedance. This same letter designation is used through the range of Eminence speakers.

I have more than one speaker in parallel – what’s the impedance?

First, let’s clarify what we mean by parallel, this is where the electrical paths through the drivers from + to – run in parallel to each other. If you trace a route from + to – you go through either one driver, or the other. The diagram below shows two speakers wired in parallel:

parallel

 To wire speakers in parallel, all you have to do is connect the + (positive or red terminal) on each speaker to the + (positive or red terminal) on your amplifier, and the corresponding – (minus or black terminal) on the speaker to the – (minus or black terminal) on your amplifier. If you plug several speakers into one amplifier, unless you have unusual cabling, this would be the standard way you would run several speakers off one amplifier.

Its normal to put speakers of the same impedance in parallel with each other, mismatching impedances isn’t a great idea unless you have a fairly advanced knowledge of speaker systems and are doing this for a specific purpose.

So what does this do to the impedance?

The impedance of each speaker stays the same, but the impedance load the amplifier sees will change. In the diagram above, if the two speakers were both 8 ohm impedance, the load the amplifier would see is 4 ohms. To think of this in simple terms, you could think of one loudspeaker as a busy road with a specific amount of traffic travelling along it, if you have two roads, the traffic can travel along either road, which presents less ‘resistance’ to the same amount of traffic. With a basic knowledge of maths, and using this analogy of two routes between start and finish, you can guess what the resistance of two parallel 8 ohm drivers would be, it’s half that of one 8 ohm driver, and is 4 ohms.

The formula for calculating parallel resistances is as follows:

parallel_formula_web

R1, R2, R3, are the individual resistances, the formula works for as many, or as few resistances there are in parallel, for two drivers in parallel, you use R1 and R2 only, for three drivers you use R1, R2 and R3.

RT is the total parallel resistance. For equal parallel resistances, the formula becomes very simple, as the table of parallel 8 ohm impedances shows:

No drivers Parallel Impedance Fraction
1 8 ohms 1/1
2 4 ohms 1/2
3 2.6 ohms 1/3
4 2 ohms 1/4
5 1.6 ohms 1/5
6 1.3 ohms 1/6

As you can see, 3 drivers gives a combined parallel impedance of one third of the original impedance of 8 ohms, and 4 drivers gives a combined parallel impedance of one quarter of the original impedance.

Very few amplifiers will run happily into impedances below 2 ohms, and there is a strong possibility you can damage the amplifier by plugging too many speakers into it. Some amplifiers will not work safely below 4 ohms, so it’s quite important to ensure you have the correct load on your amplifier.

How do I wire speakers in series?

The term series where things are arranged in sequence implies how you would arrange speakers in series, as per the diagram below you can see that the positive (+) terminal of the first speaker is connected  to the positive (+) of the amplifier as normal, but the negative  (-) terminal goes the the positive terminal of the second speaker. The last speaker in the series has it’s negative (-) terminal connected to the negative (-) terminal of the amplifier.

series_web

Series impedances work opposite to parallel, going back to the comparison with traffic, if your busy road has traffic lights in it, every extra set of traffic lights adds more resistance to traffic flow. In the same way, each loudspeaker in series adds to the impedance. To calculate the total impedance, simply add together the individual impedances, as shown in the table below. In most instances, its rare to have more than 2 drivers wired in series, as the increase in impedance will mean most amplifiers are able to deliver very little power to the drivers.

No drivers Series Impedance
1 8 ohms
2 16 ohms
3 24 ohms
4 32 ohms

 If we get less power, what’s the point of connecting drivers in series?

If you just have one pair of speakers, there isn’t much point, but it gets interesting when you have multiples of speakers. If for example you have four speakers, that are 8 ohms, and you want to run all four speakers off one amplifier, you could wire all four in parallel, to give a 2 ohm load, or all 4 in series to get a 32 ohm load. But what if your amplifier wont work below 4 ohms?

The solution is simple, a series-parallel combination:

series_parallel

 

Assuming all drivers are 8 ohms, some simple maths and you can see that each of the two series combinations has an impedance of 16 ohms. Two 16 ohm impedances in parallel have an overall impedance of 8 ohms. What this allows you to do is use four speakers where you would previously have only used one, giving you a significant increase in power handling.

Variations of series-parallel configurations are common in guitar speakers,  4 x10″ and 4 x 12″ cabinets are common, with different wiring to suit specific applications and impedance requirement. Many guitar cabinets utilise 16 ohm drivers in order to achieve the desired results.

Its sometimes advised that its best to avoid using series configurations with speakers, due to the fact that that you have two coils or inductors which can induce unwanted voltage and cause distortion. Series configurations are rarely used in hifi or studio systems.

 

 

 

 

 

 

 

1 Comment. Join the Conversation
Filed in Impedance, Loudspeaker Driver Parameters | Tagged: , , , , , ,

Impedance and Resistance – what’s the difference?

Posted By Andy Kos

Why does my 8 ohm speaker read 6 ohms when I measure it on a multimeter? It must be faulty right?

WRONG!

I’ve heard this so many times I’ve lost count, but there is a difference between impedance and resistance. When you measure resistance with a multimeter you are measuring DC resistance. The DC resistance is determined by the copper (or sometimes aluminium) wire in the voice coil of the speaker, and is actually as the name suggests; resistance to the passage of electric current through the copper. The key point here is that the electrical current travels in one direction only, and is fixed and does not change.

Impedance is equivalent to resistance, but for circuits where the voltage and current change, such as in a loudspeaker. An extra factor comes into play, which is the fact the the loudspeaker is based on a coil of wire. This coil of wire acts as an inductor. Without getting too involved in the science part of this, its sufficent to know the inductor creates an additional ‘reactance’ to alternating signals, which when added to the DC resistance of the voice coil, gives the overall Impedance.

To complicate matters further, the Impedance varies with frequency, so the 8 ohms specified for loudspeakers is not totally accurate, it is referred to as ‘nominal impedance’ – a kind of ‘average’ impedance figure that can be used for typical calculations involving loudspeakers. The graph below show a typical 18″ subwoofer, the impedance is shown on the scale on the left hand side.

impedance

For purposes of being able to run your own sound system, or building your own speakers, it’s sufficient to accept the manufacturer’s quoted impedance as being correct for your application. You don’t need to be concerned with the finer points of impedance unless you get into more serious aspects of speaker design, and if you’re at that level, I highly doubt you will have bothered read this far, as you will know all of this already!

 

Be the first to comment
Filed in Impedance, Loudspeaker Driver Parameters | Tagged: , , ,